VERTICAL CONTACT TOASTERModel VCT-2000 (Wide Mouth)Owner’s ManualP/N 1010875 Rev. C 02/13MANUFACTURINGNUMBERS:9210212 CTISLUSEDASDLISTECMOINNITATCTISL
VERTICAL CONTACT TOASTER10P/N 1010875 Rev. C 02/13Hi-Limit Reset ButtonA Hi-Limit Control turns off electrical power to the heat-er and control circui
11VERTICAL CONTACT TOASTERP/N 1010875 Rev. C 02/13OPERATION (continued)Table 2Fault CodesOLD STYLECONTROL BOARDFAULT CODE ON DISPLAYFAULT CODE DESCRIP
VERTICAL CONTACT TOASTER12P/N 1010875 Rev. C 02/13DailyCLEANING THE BLACK AND SILVER RELEASE SHEET, CONVEYOR BELT WRAPS, AND TOASTERTools Required: •
13VERTICAL CONTACT TOASTERP/N 1010875 Rev. C 02/13Replacing Belt Wraps (Every 3 to 6 months)NOTE: Depending on toaster usage and how well they are cle
VERTICAL CONTACT TOASTER14P/N 1010875 Rev. C 02/13Figure 12. Removing Conveyor Belt ChainsFigure 11. Removing Conveyor Belt ChainsRotationUpper Suppor
15VERTICAL CONTACT TOASTERP/N 1010875 Rev. C 02/13Weld ScrewsAcorn NutsSpacersTensioner Assy.TapeFigure 14. Replacing Roller Tensioner Assy.Figure 13.
VERTICAL CONTACT TOASTER16P/N 1010875 Rev. C 02/13TROUBLESHOOTINGWARNINGTo avoid possible personal injury and/or damage to the unit, inspection, test
17VERTICAL CONTACT TOASTERP/N 1010875 Rev. C 02/13TROUBLESHOOTING (continued)Problem Possible Cause Corrective ActionNoControlDisplay. Unit not plug
VERTICAL CONTACT TOASTER18P/N 1010875 Rev. C 02/13TROUBLESHOOTING (continued)Problem Possible Cause Corrective ActionCrowns and/or Heels must be force
19VERTICAL CONTACT TOASTERP/N 1010875 Rev. C 02/13Problem Possible Cause Corrective ActionToaster makes unusual sounds.Compression Settings are too t
VERTICAL CONTACT TOASTER2P/N 1010875 Rev. C 02/13GeneralThe Vertical Contact Toaster Model VCT-2000 is designed for contact toasting of buns. The toas
VERTICAL CONTACT TOASTER20P/N 1010875 Rev. C 02/13REPLACEMENT PARTSParts IdentificationPlatenHi-Limit ControlFan BladeHi-Limit Capillary ProbeA/C Freq
21VERTICAL CONTACT TOASTERP/N 1010875 Rev. C 02/13REPLACEMENT PARTS (continued)CAUTION Do not touch hot surfaces109108107106Heated Base OnlyC
VERTICAL CONTACT TOASTER22P/N 1010875 Rev. C 02/13REPLACEMENT PARTS (continued)POWERTEMPDOWNTEMPUPTEMPSCALE°C°F243268114321708717197020908991721212627
23VERTICAL CONTACT TOASTERP/N 1010875 Rev. C 02/13REPLACEMENT PARTS (continued)49941674076854251675371570787988505731191414306767959430, 9431, 9565459
VERTICAL CONTACT TOASTER24P/N 1010875 Rev. C 02/131 0011266 Conveyor Belt (Incl. items below) 2 0800204 1/2” Pitch Link, Small 2 0800121 3/4”
25VERTICAL CONTACT TOASTERP/N 1010875 Rev. C 02/13WIRING DIAGRAMPictorial Wiring Diagram Heated Base UnitsFAN21+3-43-32 VDC240 VACINTERLOCK SWITCH# 18
VERTICAL CONTACT TOASTER26P/N 1010875 Rev. C 02/13FAN21+3-43-32 VDC240 VACINTERLOCK SWITCH# 18 GA. AWM-105°C* 16 GA. TFE-200°C 22 GA. AWM-105°C
27VERTICAL CONTACT TOASTERP/N 1010875 Rev. C 02/13WIRING DIAGRAM (continued)HI-LIMITCONTROLPOWER SWITCH240 VACLINE FILTERGL1L2S.S. RELAY 2S.S. RELAY 1
LIMITED WARRANTYEquipmentmanufacturedbyRoundupFoodEquipmentDivisionofA.J.Antunes&Co.hasbeencon-structed of the finest materials avai
3VERTICAL CONTACT TOASTERP/N 1010875 Rev. C 02/13Refer to the service agency directory included with your unit.Authorized Service AgencyName:Phone No.
VERTICAL CONTACT TOASTER4P/N 1010875 Rev. C 02/13In addition to the warnings and cautions in this manual, use the following guidelines for safe operat
5VERTICAL CONTACT TOASTERP/N 1010875 Rev. C 02/1321 1/4”(540 mm)23 1/4"(591 mm)10 3/4"(273 mm)15 1/4”(387 mm)DimensionsSPECIFICATIONSElectri
VERTICAL CONTACT TOASTER6P/N 1010875 Rev. C 02/13WARNINGELECTRICAL SHOCK HAZARD. FAILURE TO FOLLOW THE INSTRUCTIONS IN THIS MANUAL COULD RESULT IN SER
7VERTICAL CONTACT TOASTERP/N 1010875 Rev. C 02/13Conveyor Safety Interlock SwitchBun Feeder (some models only)Heat ShieldRelease Sheet Retainer ClipsB
VERTICAL CONTACT TOASTER8P/N 1010875 Rev. C 02/13NOTE: The toaster is tested and shipped with the heaters set at the above recommended temperatures.OP
9VERTICAL CONTACT TOASTERP/N 1010875 Rev. C 02/13Temperature control panelNOTE: The term “setpoint temperature” refers to the desired temperature set
Commentaires sur ces manuels